Gas Lift Design, Optimization & Troubleshooting
Have Questions ?
Gas Lift Design, Optimization & Troubleshooting - PE-GLD-PEA27
| Code | Date | Time | Duration | Location | Currency | Early Bird Fee Per Person |
|---|---|---|---|---|---|---|
| PE-GLD-PEA27 | 26 - 30 Apr 2027 | 10 AM CST | 4 Hours Per Day |
Online |
USD |
3000 |
Need this for a group? We deliver the same course in-house — face-to-face at your location or online — tailored to your assets and team level. Contact info@peassociations.com.
Boost your team's skills and your budget! Enjoy group discounts for collaborative learning. Send an inquiry to info@peassociations.com.
Gas Lift Design, Optimization & Troubleshooting
Description
Gas lift is the most tolerant artificial lift method for deviated, gassy and sand-producing wells, and it is widely used offshore where reliability matters most. Its apparent simplicity hides a design that must be done carefully: unloading valves have to open and close in sequence, the injection point has to be as deep as available pressure allows, and gas has to be distributed between wells in a way that maximises total production.
This course
covers gas lift design in full. It begins with continuous and intermittent gas
lift principles, gas lift performance curves and the effect of injection rate
on well production. It then covers valve mechanics for injection pressure operated
and production pressure operated valves, unloading sequence design, valve
spacing and test rack setting. The second half covers gas allocation and
optimisation across a field, surveillance methods including flowing gradient
surveys and injection rate tests, and the diagnosis of common problems such as
multipointing, heading, valve leaks and inadequate injection pressure.
Gas lift works by injecting gas into the production tubing to reduce the density of the fluid column so that the reservoir can lift it to surface. How much production the well makes depends on how deep the gas is injected and how much is injected. Deeper injection lightens more of the column; more gas lightens it further until friction losses begin to outweigh the density benefit.
The design problem is to reach the deepest possible injection point with the available injection pressure, and to get there through a sequence of unloading valves that open and close in the right order as the annulus is unloaded. If valve spacing, port sizes and test rack settings are wrong, the well may inject through several valves at once, fail to reach the operating valve, or cycle unstably.
At field level, the problem becomes one of allocation. Compression capacity is limited, and giving more gas to a well that is already past its optimum takes gas from a well that would use it better. Common failings include allocating gas by habit, leaving designs unchanged as water cut and reservoir pressure change, and not surveying wells often enough to know where gas is actually going.
By the end of this training, participants will be able to:
- Explain the principles of continuous and intermittent gas lift and where each applies.
- Construct gas lift performance curves and identify the optimum injection rate.
- Describe the mechanics of injection pressure operated and production pressure operated valves.
- Design the unloading sequence and select valve spacing for a given well.
- Calculate valve port sizes and test rack setting pressures.
- Determine the deepest achievable injection point for the available injection pressure.
- Allocate lift gas across a field to maximise total production within compression limits.
- Plan and interpret gas lift surveillance, including flowing gradient surveys and injection tests.
- Diagnose multipointing, heading, valve leaks and other common gas lift problems.
Organisations sending participants to this training will:
- Get gas lift designs that reach the intended injection depth and perform as predicted.
- Increase field production through better allocation of limited lift gas.
- Reduce unstable wells and the production losses they cause.
- Diagnose gas lift problems without unnecessary interventions.
- Keep gas lift designs current as reservoir and well conditions change.
Participants will:
- Understand gas lift design from first principles.
- Be able to design unloading strings and set valves correctly.
- Be able to optimise injection rates on individual wells and across a field.
- Be able to interpret gradient surveys and injection test data.
- Be able to diagnose the common causes of gas lift underperformance.
- Production engineers
- Artificial lift engineers
- Well operations engineers and supervisors
- Production technologists
- Completion engineers working on gas lift wells
- Field technicians responsible for gas lift wells
Module 1: Gas Lift Principles
- Continuous and intermittent gas lift
- Effect of injection on the flowing gradient
- Gas lift performance curves
- Applications and limitations
Module 2: Gas Lift System Components
- Mandrels and side pocket mandrels
- Valve types and their construction
- Surface injection and control equipment
- Compression and gas distribution systems
Module 3: Valve Mechanics
- Injection pressure operated valves
- Production pressure operated valves
- Force balance equations
- Orifice valves and venturi valves
Module 4: Continuous Gas Lift Design
- Design basis: inflow, outflow and available injection pressure
- Determining the injection point
- Unloading sequence
- Valve spacing methods
- Port size selection and test rack settings
Module 5: Intermittent Gas Lift and Chamber Lift
- Intermittent lift cycle
- Design considerations
- Chamber lift and plunger-assisted gas lift
Module 6: Gas Lift Optimisation
- Injection rate optimisation for a single well
- Gas allocation across a field
- Compression and gas supply constraints
- Effect of water cut and reservoir pressure changes
Module 7: Surveillance
- Flowing gradient surveys
- Injection rate and pressure tests
- Acoustic and downhole gauge data
- Routine surveillance programmes
Module 8: Troubleshooting
- Multipointing and injection through the wrong valve
- Heading and instability
- Valve leaks, cutting and failure
- Insufficient injection pressure
- Tubing and annulus communication problems
Upon successful completion of this training course, delegates will be awarded an official Certificate of Completion issued by the Petroleum Engineers Association (PEA), an ISO 9001:2015 certified training organization. The certificate carries 10 Credits and formally records the total learning hours completed.
Each certificate is signed by the Course Facilitator and the CEO of the Petroleum Engineers Association, and serves as verifiable proof of professional training that delegates can present to employers and professional bodies worldwide.
Frequently Asked Questions
All course bookings made through PEA are strictly non-refundable. By registering for a course, you acknowledge and accept that all fees are payable in full and are not subject to refund under any circumstances, including changes in personal or professional commitments or partial attendance.
PEA reserves the right to make reasonable adjustments to course content, trainers, or schedules where necessary, without entitling delegates to a refund. Comprehensive details of each course — including objectives, target audience, and content — are clearly outlined before enrolment, and it is the responsibility of the delegate to ensure the course's suitability prior to booking.
For any inquiries related to cancellations or bookings, please contact our support team, who will be happy to assist you.